I've pulled an Alpine CDA-117 with an Imprint PXA-H100 out of my old car and have been debating whether or not to use it in my new car build. The alternative being, buy a 4200nex and minidsp 6x8 to replace it. The main motivating factor for the 4200nex is basically android auto. Home of the Auto-Tune plug-in, the music industry standard for pitch correction and vocal effects. Shop and learn about the best plug-ins for pitch correction, vocal effects, voice processing, and noise reduction. Auto-Tune Pro, Auto-Tune Artist, Auto-Tune EFX+, Auto-Tune Access, Harmony Engine, Mic Mod and more. Aug 14, 2019  Foreword: Up for review is the MiniDSP C-DSP 8x12 with Dirac Live. This can be purchased directly from miniDSP.com or through Parts-Express. While this review is intended to provide insight in to the use and subjective opinion of the end result of the MiniDSP with Dirac Live, it is not intended to be a full tutorial on how to tune with Dirac Live. Sep 15, 2015  Car audio DSP - miniDSP based 12 posts. The only commercial systems with auto tune are more like audyssey in home theater where they don't allow ANY manual control after the. . Digital Room Correction: Last but not least, few miniDSP platforms can also provide accurate Digital Room correction. This process easily tunes your room by removing the guess-work. So to summarize this application note, flat frequency response of a system will not happen by the magic of a DSP (no matter which brand it is). MiniDSP UMIK-1 Omnidirectional USB Measurement Microphone The UMIK-1 is an omni-directional USB measurement microphone providing Plug & Play acoustic measurement. From speaker & room acoustic measurement to recording, this microphone provides low noise and accurate results you can rely on.

• Minidsp Auto Tune Accurate Service
• Voice Changer
• Autotune Download
• Minidsp Auto Tune Accurate Site

Welcome to the world of system tuning and DSP!

There isn't much to argue on the fact that speaker building is an art requiring time and understanding of acoustic theories. While some simulation software may help for the design of your enclosure, audio measurements are the basis for any evaluation of your system. No matter how pretty your box is or the choice of high specs drivers, your 'system' (i.e. enclosure + speakers + crossover) may very well have poor specifications if it isn't properly tuned (equalization/time alignment).

Thanks to the partnership between the miniDSP platforms and the well known freeware Room Eq Wizard (REW), miniDSP is much more than a digital audio processor. By providing a complete measurement + system tuning solution fitting in the palm of your hand, the miniDSP product line innovates once again, yet keeping our price very competitive.

What's needed?

You will need:

• A miniDSP plugin that supports the 'REW integration' feature. (Suitable examples includes the Advanced 2-way, Advanced 2.1, Advanced 4-way, and the 2x8, 4x8, 4x10 and 10x10 Crossovers.)
• The miniDSP hardware that runs the plugin - see the 'Supported platforms' row on the plugin page linked above.
• Room EQ Wizard (REW), which is a free download from Home Theater Shack.
• A measurement microphone, such as the UMIK-1.

Minidsp Auto Tune Accurate Service

1. Make the initial measurement

In the miniDSP interface, disable all equalization and crossover filters on your subwoofer. Turn off all amps except the subwoofer amp(s), or disable the other outputs in the miniDSP interface. This is so you can measure the 'raw' subwoofer response.

Then, in REW, run a measurement sweep from 10 Hz to 300 Hz. Ensure that your SPL is adequate to get a clean measurement.

2. Calculate the correction filters in REW

From the REW main screen, open the 'EQ' tab.

Is there a program like little snitch on windows 10. Set the parameters as shown in the following screenshot. Note that in the Equaliser section you will need to select 'MiniDSP' for plugins running at 48 kHz, and 'MiniDSP-96k' for plugins running at 96 kHz.

Next, click on 'Set Target Level' to set the target level to REW's recommendation. (You can manually change it later.)

Then click on 'Match Response to Target.' REW will generate filters to optimize the response and display the predicted response (response after correction). Here is an example with the measured response in dark blue and the predicted response in light blue:

You can see the filter settings calculated by REW by clicking on the 'EQ Filters' button near the top of the screen:

In this example, only three filters were needed. If REW uses a lot of filters or uses filters with very high Q (> 20), experiment with the target level setting to try and get a smoother correction curve. You can also experiment with the flatness target and the max boost settings to get the best predicted response.

3. Load the correction filters into the miniDSP

Once the predicted response is satisfactory, click on 'Send Filter Settings to Equaliser' and save the settings as a file.

Then, in the miniDSP plugin, navigate to the Parametric EQ block that will be equalizing the subwoofer. Set it to 'Advanced' mode and click on 'Import REW File.' Select the file that you just saved, and the plugin will then display the correction filter:

Confirm your result by running your measurement sweep again - it should be much smoother than before! Here in light blue is the new measurement, compared to the original measurement in dark blue - as you can see, the measured result is almost identical to REW's prediction:

4. Integrate the subwoofer

In the crossover block in the miniDSP interface, re-enable the subwoofer's low pass filter. If you have a ported sub, you may wish to also add a high pass filter to protect the sub from over-excursion at high levels and low frequencies.

Then enable the other outputs (main speakers or drivers) and run full-range measurement sweeps. If there is a bump or dip at the crossover point, try adjusting the crossover settings (frequency, slope, phase) and the time delay of the subwoofer to flatten it out.

Next steps

Once you have mastered the above procedure, you can improve your system even further:

Voice Changer

• Try different subwoofer locations to find the one with the smoothest response. The smoother the response without equalization, the better the result will be with equalization!
• Make several measurements around the listening area, and in the REW All SPL tab, click on 'Average the Responses.' Then use that average for the EQ calculation.
• If you have a sealed sub, apply a Linkwitz Transform.

You will now have the smoothest bass response you could imagine! Don't forget to ask on the miniDSP forum if you have questions.

How to Convert a Regular Room to a Home Theater

Autotune Download

So you've got the itch to put in a home theater. But, how does one go about doing this and what room should you use? This quick guide gives you a step by step procedure to make it a reality. Be sure to watch our related YouTube video and check out all of the embedded article links to dive further into each topic. Also, feel free to share your stories and pics on our related forum thread for the benefit of our community.

Minidsp Auto Tune Accurate Site

So you've got the itch to put in a home theater. But, how does one go about doing this and what room should you use? This quick guide and YouTube video gives you a step by step procedure.